显示标签为“304 stainless steel coils”的博文。显示所有博文
显示标签为“304 stainless steel coils”的博文。显示所有博文

2016年6月27日星期一

[ Wiki ]STAINLESS STEEL FINISHING OPTIONS

There are a number of stainless steel finishing options that alter more than just the appearance of the material. Whatever the intended use, choosing the right finish option is essential.
In projects when design is a primary consideration, an attractive finish will enhance the appeal of the end-product. For example, in architecture and the automotive industries, different finishes can be used to achieve a variety of visual effects. In retail products, particularly kitchen appliances, stainless steel No. 4 finish is one of the most popular finishes available.
The choice of surface finish is also important where fabrication processes will be applied. Rough surface finishes are appropriate when the steel will be ground prior to painting and gluing. Smooth surface finishes are better where the steel will be blended.
The choice of finish should always be clearly specified and properly defined by standard industry designations.

THE DEVELOPMENT OF THE SURFACE FINISH STANDARD

During the late 1970’s, British Steel scientists found that dull polished finishes on stainless steel showed a wide range of surface roughness. Further testing revealed that steel with high surface roughness was heavily damaged by the polishing operations, whereas steel with low surface roughness was relatively unscathed.
During the mid-1980’s dull polished finishes became widely used on projects such as high-profile architectural projects. However, it was soon discovered that some of these dull polished finishes had poor corrosion resistance, especially when exposed to seawater. Consequently a new surface finish description was introduced which remains in use to this day.
Three more common stainless steel finishing options are:
  1. No. 2B – Matte finish
  2. No. 4 – Brushed finish
  3. No.8 – Mirror finish

NO. 2B – MATTE FINISH

stainless steel finishing options - 2B
No. 2B – Matte Finish
No. 2B is the mill finish, meaning it has not been processed further. Matte finishes are dull in appearance and are not ideal for atheistic end uses. However, they’re a good choice where appearance is not important or when further finishing is intended. No. 2B Matte finishes are the least expensive of the stainless steel finishing options.
The finish is produced by ‘cold rolling’ stainless steel through special rolls or dies. The cold rolling produces a smoother, less pitted surface. Next it is softened and de-scaled in acid solution. The steel is given a final pass on polished rolls to further enhance its smoothness.
Common applications include:
  • Chemical plant equipment
  • Pharmaceutical equipment
  • Paper mill equipment
  • Laundry and dry cleaning
  • Refrigeration
  • Sewage equipment

NO. 4 – BRUSHED FINISH

stainless steel finishing options - no. 4
No. 4 Brushed Finish
The No. 4 Brushed finish can vary with different suppliers and even from batch to batch from the same supplier. The variations arise from differing manufacturing conditions, such as wearing of the abrasive belts used in these finishes. Some level of variation should be expected when ordering No. 4 Brushed finish. It can be helpful to request a sample of a few square inches to ensure the finish achieves the desired effect.
Brushing the stainless steel produces a distinctive look with a muted luster and a pattern of fine parallel lines. It has strong decorative appeal without being too reflective, as too much reflectiveness can be undesirable. For example, overly reflective stainless steel accents on a building could be blinding in bright sunlight. The drawbacks to this finish include reduced corrosion resistance, because the grooves of the finish are susceptible to rust.
The finish is created by sanding the stainless steel in one direction with a 120-180 grit belt, followed by softening with a 80-120 grit medium non-woven belt.
brushed stainless steel finishing options
Gateway Arch
Common applications include:
  • Jewelry and watches
  • Home appliances
  • Air conditioners
  • Water heaters
  • Architecture
  • Automotive design
The Gateway Arch in St Louis, Missouri is the world’s tallest arch and is clad in brushed stainless steel.
The DeLorean DMC-12 sports car, most famous for being featured in the Back to the Future films, is paneled in brushed stainless steel.

NO.8 – MIRROR FINISH

Mirror finishes are highly reflective and created by polishing the stainless steel. The polishing process enhances appearance and consistency, making cleaning easier. It also masks the after-effects of welding and hides surface damage.
No. 8 Mirror finish is created by mechanically treating the surface with a series of progressively finer abrasives. Alternatively a special rolling procedure is used which can simulate the appearance of mechanical abrasion. For this stage, it is essential to remove deep scratches as any surface defects will be very noticeable on the finished product. The final process involves buffing the surface for 5-10 minutes to create a mirror-like, highly reflective finish.
A benefit of No. 8 Mirror finishing is that it improves corrosion resistance. The polishing eradicates crevices where corrosive particles can lodge themselves.
Common applications include:
  • Mirrors
  • Ornamental trim
  • Clean rooms
  • Column covers
  • Wall panels
  • Reflectors

[ Wiki ] DIFFERENCE BETWEEN ANNEALING AND TEMPERING

HEAT TREATMENTS


Heat treatments are used to alter the physical and mechanical properties of metal without changing its shape. They are essential processes in metal manufacturing which increase desirable characteristic of metal, while allowing for further processing to take place.
Various heat treatment processes involve carefully controlled heating and cooling of metal. Steel, for example, is commonly heat treated for use in a variety of commercial applications.
Common objectives of heat treatment are to:
  • Increase strength
  • Increase hardness
  • Improve toughness
  • Improve machining
  • Improve formability
  • Increase ductility
  • Improve elasticity
How Heat Affects Metal
The cooling stage has different effects depending on the metal and process. When steel is cooled quickly it hardens, whereas the rapid cooling stage of solution annealing will soften aluminum.
While there are many types of heat treatment, two important types are annealing and tempering.

ANNEALING


Annealing involves heating steel to a specified temperature and then cooling at a very slow and controlled rate.
Annealing is commonly used to:
  • Soften a metal for cold working
  • Improve machinability
  • Enhance electrical conductivity
Annealing also restores ductility. During cold working, the metal can become hardened to the extent that any more work will result in cracking. By annealing the metal beforehand, cold working can take place without any risk of cracking, as annealing releases mechanical stresses produced during machining or grinding.
Annealing is used for steel, however, other metals including copper, aluminum and brass can be subject to a process called solution annealed.
Large ovens are used for annealing steel. The inside of the oven must be large enough to allow air to circulate around the metal. For large pieces, gas fired conveyor furnaces are used while car-bottom furnaces are more practical for smaller pieces of metal.
During the annealing process, the metal is heated to a specific temperature where recrystallization can occur. At this stage, any defects caused by deformation of the metal are repaired. The metal is held at that temperature for a fixed period, then cooled down to room temperature.
The cooling process must be done very slowly to produce a refined microstructure, thus maximizing softness. This is often done by immersing the hot steel in sand, ashes or other substances with low heat conductivity, or by switching off the oven and allowing the steel to cool with the furnace.

TEMPERING


Tempering is used to increase the toughness of iron alloys, particularly steel. Untempered steel is very hard but is too brittle for most applications. Tempering is commonly done after hardening to reduce excess hardness.
Tempering is used to alter:
  • Hardness
  • Ductility
  • Toughness
  • Strength
  • Structural stability
Tempering involves heating the metal to a precise temperature below the critical point, and is often done in air, vacuum or inert atmospheres.
The temperature is adjusted depending on the amount of hardness that needs to be reduced. While it varies depending on the metal type, generally, low temperatures will reduce brittleness while maintaining most of the hardness, while higher temperatures reduce hardness which increases elasticity and plasticity, but causes some yield and tensile strength to be lost.
It is essential to heat the metal gradually to avoid the steel being cracked. The metal is then held at this temperature for a fixed period. A rough guideline is one hour per inch of thickness. During this time the internal stresses in the metal are relieved. The metal is then cooled in still air.

HOW IS STAINLESS STEEL MADE?

Stainless steel is known for excellent corrosion resistance. It is an integral part of modern life and is used in a range of applications, including heavy industry, architecture, automotive manufacture, surgery and dentistry.
Until the 1950s and 1960s, which saw the development of AOD (argon oxygen decarburization) and VOD (vacuum oxygen decarburization), the processes to produce stainless steel were slow and expensive. However, these two developments revolutionized stainless steelmaking and significantly decreased the raw material costs, increased productivity, and improved quality. This led to dramatic growth of steelmaking from the 1970s until the present.

HOW IS STAINLESS STEEL MADE?

Raw materials

Stainless steel is an iron alloy with added elements such as chromium, nickel, silicon, manganese, nitrogen and carbon. The properties of the final alloy can be fine-tuned by altering the amounts of the various elements.

The importance of chromium in making stainless steel

Chromium is essential for the production of stainless steel; in fact there’s no viable alternative. Chromium is a hard, corrosion-resistant transition element that gives stainless steel its corrosion resistance. In general, the higher the chromium content, the more corrosion-resistant the steel.

The manufacturing process

Melting
The raw materials are melted together in an electric arc furnace. It can take 8 to 12 hours of intense heat until the metal becomes molten.
Removal of carbon content
The next stage is to remove excess carbon. This is done by processing the molten metal in an AOD (Argon Oxygen Decarburization) converter. The converter reduces the carbon by injecting an oxygen-argon mixture. At this stage, further alloying elements like nickel and molybdenum can be added to the AOD converter.
Alternatively a VOD (Vacuum Oxygen Decarburization) converter can be used to when a very low carbon content is required.
Tuning
Most stainless steels have exacting quality requirements. The tuning process allows fine adjustments to the chemical composition. Tuning is when the steel is slowly stirred to remove unwanted elements and improve consistency, while maintaining the required composition within the temperature limits.
Forming
Now the molten steel is cast into forms. These forms can be blooms (rectangular shapes), billets (round orsquare shapes), slabs, rods or tubes.
Hot rolling
Hot rolling occurs at a temperature above the recrystallization temperature of the steel. The precise temperature depends on the desired stainless steel grade. The steel forms are heated and passed through high rolls. Blooms and billets are formed into bar and wire. Slabs are formed into plate, strip, and sheet.
Cold rolling
Cold rolling is used where extremely precise dimensions or an attractive finish are required. The process occurs below the recrystallization temperature of the steel. Cold rolling is carried out using small-diameter rolls and a series of supporting rolls. This process allows the production of wide sheets with improved surface finishes.
Annealing
Annealing is the process used to soften stainless steel, improve ductility, and refine grain structure. It is also used to relieve internal stresses in the metal caused by previous processing. During the annealing process the steel is heated and cooled under controlled conditions.
Descaling
The annealing process causes scale to form on the steel. These scales are commonly removed using pickling, which involves bathing the steel in nitric-hydrofluoric acid. Electrocleaning is an alternative method which uses an electric current to remove the scale.
Cutting
The stainless steel can now be cut to the desired size. Mechanical cutting is the most common method. The stainless steel can be straight sheared with guillotine knives, circle sheared using circular knives, sawed using high-speed blades, or blanked with punches and dies. Other methods include flame cutting, which uses a flame-fired torch powered with oxygen, propane, and iron powder, or Plasma Jet cutting which uses an ionized gas column in conjunction with an electric arc to cut the metal.
Finishing
Surface finish is important for stainless steel products, especially in applications where appearances are important. While most people are familiar with the look of stainless steel used for consumer products, there are actually a number of finishing options.
Grinding wheels or abrasive belts are commonly used to grind or polish the steel. Other methods include buffing with cloth wheels with abrasive particles, dry etching using sandblasting, and wet etching using acid solutions. The smooth surface provides better corrosion resistance.